NATURAL OIL WOODSTAIN

BACK

INNOVATIVE AND DURABLE PROTECTION

Base and top coat in one finish
Satin and Matt finishes available
Fast drying
Natural wood grain remains visible
Extremely weather and UV resistant
Very water and dirt resistant
Resistant against algae, mould, mildew and fungal attack
Reduces wood swelling and shrinkage
Microporous, breathable finish which does not crack, peel or flake
No sanding necessary for future application

BUY NOW

Documentation

700 PINE

UV-Resistance:★★★★

701 CLEAR, MATT

UV-Resistance: None

702 LARCH

UV-Resistance: ★★★★

703 MAHOGANY

UV-Resistance: ★★★★

706 OAK

UV-Resistance: ★★★★

707 WALNUT

UV-Resistance: ★★★★

708 TEAK

UV-Resistance: ★★★★

710 STONE PINE

UV-Resistance: ★★★

712 EBONY

UV-Resistance: ★★★★★

727 ROSEWOOD

UV-Resistance: ★★★★★

728 RED CEDAR

UV-Resistance: ★★★★

729 FIR GREEN

UV-Resistance: ★★★★

731 OREGON PINE

UV-Resistance: ★★★★

732 LIGHT OAK

UV-Resistance: ★★★★

900 WHITE

UV-Resistance: ★★★★

903 BASALT GREY

UV-Resistance: ★★★★

905 PATINA

UV-Resistance: ★★★★

906 PEARL GREY

UV-Resistance: ★★★★

907 QUARTZ GREY

UV-Resistance: ★★★★

FINISH

Clear Finish: Matt only.

Transparent Colour Finishes:
18 colours in Satin or NEW Matt* finish.

*Product only available when mixed in selected stores,
via the Osmo Tinting Machine.

APPLICATION TOOLS

Osmo Flat Brush or Osmo Microfibre Roller

RECOMMENDED USE

Exterior wood surfaces

RECOAT

One coat, when signs of wear become visible

SIZES

5ml, 125ml, 750ml, 2.5L

DRY TIME

First coat: 4-6 hours, Second coat: 12 hours

CLEAN UP

Osmo Brush Cleaner

COVERAGE

26m²/L with one coat

COATS

2 coats

CARE

Osmo Spray Cleaner

SURFACE PREPARATION

Wood surface must be clean, dry and frost-free (moisture content max. 20%).Osmo Natural Oil Woodstain is ready to use. Do not thin. Stir well before use.
If possible, please apply the first coat to all sides before installation. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works.
The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat.

NOTE

Transparent colours are influenced by the natural colour of the wood and therefore they may deviate from the sample colours. Light transparent colour tones offer only limited UV protection; therefore they are not recommended for surfaces exposed to strong sunlight. Dried surface is at first satin-glossy and then satin. To extend the life of the coating, it is recommended to apply one final top coat of Osmo UV Protection Oil Extra 420 Clear after thoroughly drying (not recommended for White 900). Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. All colour tones can be mixed with each other.
Starting from 2.5 litres per colour tone, available in 186 RAL Classic and 1950 NCS colour tones.
Transparent finishes allow the substrate to shine through. Depending on the wood species, the appearance of the colour tone may deviate from the original RAL/NCS colour tone.
Osmo Natural Oil Woodstain is furnished with biocides and therefore it is only to be used in outdoor areas.
The added active ingredients delay or minimise the risk of algae and fungal attack. For effective protection, two coats are to be carried out. In accordance with the latest technical research, permanent protection against algae and fungal attack cannot be provided.

Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating.

METHODS OF APPLICATION

With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well.
Allow to dry for approx. 4-6 hours under good ventilation. Then apply a second coat.
For renovation works, one coat applied to the clean and dry surface is usually sufficient.

NOTE

Regular Cleaning: Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush.

Occasional Maintenance: If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean.

Recoating: Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.

OSMO FLAT BRUSH

Made with high quality synthetic bristles with soft tips which gives fine control in achieving the desired effect. Exceptional coverage capacities which produce professional looking results every time. Available in 25, 50, 60 and 100 mm sizes.

OSMO SMALL ROLLER SET

Microfibre roller and 60mm natural bristle brush set to ensure high coverage allowing you to apply thinly, thoroughly and evenly along the wood grain and spread well. For first application, two coats is recommended onto a clean and dry surface. For renovation, just one coat is necessary.

Top Tips:

For new resinous wood species, please allow approx. three months exposure to the outside elements prior to application.
The transparent colour tone of the finish will be influenced by the wood’s natural colour, and testing first is always recommended.
Over application can increase the drying times.
Use biocides safely. Always read the label and product information before use.
Recommended application amount is approx. 35 ml/m².
Drying time of 4-6 hrs after the first coat, but is 12 hours after both coats have been applied.
If the subsurface does not absorb the wood finish uniformly, the colouration will be uneven. For an improved, consistent and matted surface, we recommend retreating the surface with [701 Clear]. Thereby glossy spots are matted and an even appearance is created.
Grey wood looks classically beautiful, to allow the natural greying process to occur, apply [701 Clear].
For more grey colour tones for an aged and weathered effect, see Osmo Natural Oil Woodstain Effect.
Multi-purpose cleaners such as washing up liquids and detergents are highly detrimental to the finished surface and is not recommended to be used as discolouration or staining may be possible.
Other household cleaning products such as vanish, bleach, baking soda etc. are likely to cause severe discolouration or staining.
Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered.

Additional Information:

Approx. coverage: 26m²/L with one coat
No. of coats: 2
Ideal application temperature: +10°C to 35°C
Drying time: 4-6 hrs.
Sizes: 0.125L, 0.750L, 2.5L

A decorative, oil-based protective finish for all exterior use.

The microporous, breathable finish allows the wood to breath

and reduces the risk of swelling and shrinkage. Water repellent and extremely weather and UV resistant.

Contains active ingredients to slow growth of mildew, algae and fungal. Proven finish over decades in all kinds of climatic conditions – does not crack, flake, peel or blister.

RECOMMENDED AFTER WEATHERING PERIOD

For the following wood types, a weathering period is recommended. New or sanded wood requires at least 12 weeks (approximate) exposure to the exterior elements before application.

After the weathering period, it’s generally recommended to de-grey the surface with Osmo Wood Reviver Power-Gel and clean the surface from the extractive content before application, always trial apply!

For all other ingredient-rich hardwood species not mentioned may require a varied period of exposure. Please contact us for further information.

ALSO RECOMMENDED

❌ Green Oak: moisture content is often above the maximum 20% recommended.

❌ Idigbo: contains yellow dyes which leaches when the wood becomes wet and stains when in contact within iron.

❌ Other: woods treated with a varnish, lacquer or other surface coatings must be completely sanded before use

ALSO RECOMMENDED

For the following wood types, WR Base Coat is recommended before use.

Accoya®
Kebony®
Pine
Douglas Fir
Spruce

Cedar
Iroko
Mahogany
Teak
Walnut
Ipe
Merbau
Wenge
Rosewood
Sycamore
Pressure-Impregnated Pine
Sapele: 3-4 weeks exposure
Larch: 2 weeks exposure. Application of WR Base Coat is recommended before use.